Installation Manual for DRS-1CH

 

 

    Table of Contents

1.  Product Overview
2.  What’s in the box
3.  Installation Instructions
4.  Basic Operation
5.  App Introduction
6.  Troubleshooting Instructions
7.  Specifications

 

    1. Product Overview

Our Aeion Dashcam continuously records the view through the front or rear windscreen, providing video evidence in case of accidents, traffic violations, or other road incidents. Below you can find the product specifications for the S-series.

No.	Type	Description
1-	SD Card Slot	For memory card insertion
2-	USB power interface	For power supply to dashcam
3-	Speaker	For voice prompts from camera
4-	Lens	Camera lens
5-	Windshield Mount	To mount the dashcam on windshield      of your car
6-	Power button	A. When connected to an external power supply, press and hold for 2 seconds to turn on/off, and press and hold for 5 seconds to reset; Press once to start/stop recording B. This button has no effect if the external power supply is not connected
7-	Status Indicator Light	Blue indicator status (blinks slowly while recording, steady on when not recording, blinks at short intervals when firmware is being updated)
8-	Reset Button	To force restart and reset the dashcam

     2. What’s in the box

    3. Installation Instructions

1. 
   1. Insert the micro SD card into the dash cam (maximum support of 64 GB).

Please make sure the camera is turned OFF. Then align the gold-plated contacts facing towards the back of the camera (next to the R key).

The camera comes with the default settings, allowing you to start using your camera right out of the box. Please make sure to format the memory card before first use.

2. Clean the spot on your windshield where you would like to mount the camera and confirm the placement. We recommend installing the camera near the rearview mirror of the driver’s opposite side.

3. Use the pry tool to lift the edges of the windshield trim/molding and tuck in the power cord.

 4. Plug the supplied cigarette lighter power adapter into your vehicle accessory port and the other end into the dashcam's USB port. Route the cable alongside the interior trim for a better look.

4.  

   4. Basic Operation

   
   POWERING ON

   The device will power on automatically when connected to the power and it can also be powered by pressing the power button.

   POWERING OFF

   When power is disconnected the device will save the last video file and power off.

   VIDEO RECORDING

   After the car engine is switched on, the camera will automatically turn on and start recording.
   
   
   

   5. App Introduction
   

   You can use the Aeion App to connect to the dashcam's wifi, access videos, and manage camera settings.
   
   DOWNLOAD & SETUP
   
   1.  Search for "Aeion" on Google Play and "AeionCam" on App Store or scan the QR code on the first page of this manual.
   
   2. Open the Aeion App and tap "Connect to Camera via Wi-Fi"

   1. 
      
      3.  Allow app permissions. 
      4. Select DRS in the camera list and tap "Continue"
      
      
      
      5. Tap on Aeion DRS-1CH in the network list and connect to the camera Password is "aeion123"
      
      
      
      6. Tap on the camera name to live view and see recorded videos.
      
      
      
      
      7. Tap on the dots beside the camera name to access the camera settings.
      
      
      
      
      
      

   6. Troubleshooting Instructions:

   1. If the dashcam stops recording due to uncertain reasons, press the power button for 2 seconds to turn it off and turn it back on by pressing the button.
   2. If the problem persists, take out the SD card, save the recordings, format the SD card, and restart the dashcam.
   3. If the dashcam gives a "Video Recording Error" it could be due to the slow read/write speed of the SD Card, using third-party SD cards might lower the dashcam performance. Make sure to use genuine AEION SD cards.
   4. If the video is blurry, check if the lens has any dirt or foreign matter attached, and remove the dirt on the camera lens with a clean cloth.
   5. If the app's live view fails to connect, please turn off the Wi-Fi on your mobile phone and reconnect to the Wi-Fi.

   6. Please contact our customer support at cs@aeion.io if you face any issues with the camera.

5.  

   7. Specifications